Roland PNC-900 Instrukcja Użytkownika

ROLAND DG CORPOR ATIONDESK TOP SIGN MAKERUSER'S MANUAL

4• Operation PanelPOWER/ERROR LEDThis lights up when the power is switchedon, and flashes when an error is generated.SETUP LEDThis lights up when the

54 BASIC OPERATION4-1 Making the Connection with the Computer* Always make sure that the power is off on both the computer and the PNC-900 wheneverany

64-3 Installing the Blade* Always make sure the power switch is off before installing (or replacing) the blade.To prevent injuries, be very careful wh

74-4 Loading the Sheet — SETUP Key• Turning on the Power* When the power switch is pressed to turn on the unit, the tool carriage moves. Take careto

8• About the Cutting AreaUse the , , , and keys to move the tool carriageto the position on the sheet where the origin point is to be set.ORIGIN

94-6 Cutting Test to Check Blade Force — , , , , andTEST KeysBefore carrying out actual cutting, you may wish to perform a "cutting test"

104-7 Downloading Cutting DataThe unit will begin cutting when it receives cutting data sent from the computer.• Software SettingsWhen cutting with co

11• Continuing CuttingCutting After Changing the SheetAgain carry out the procedure described from "Loading the Sheet" on page 7 to "4-

12(3)Stick application tape over the completed work.Press down firmly on the application sheet to remove airbubbles. If you do not press firmly enoug

135 SETTINGS FOR EACH FUNCTION• Using the Sheet Effectively(Rotate function) — ROTATE Key and ROTATE LEDIf there is still unused material on the right

CAUTION1) Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.2) The contents of this operation manual and the spec

14• Plotting on Paper Media — PEN MODE Key and PEN MODE LEDThe PNC-900 is also capable of plotting on paper media using plotter pens made by this comp

156 ABOUT THE BLADEIf the blade becomes dullWhen the blade starts to lose its sharpness, try gradually increasing the blade force (refer to page 8, &q

167 WHAT TO DO IF...If the PNC-900 doesn't run...PNC-900• Is the PNC-900 power on?Turn on the power.• Is the unit in SETUP status (the SETUP LED

17• If you are using a program that you have created yourself, have correct commands been sent?The PNC-900 is equipped with the CAMM-GL III instructio

188 LIST OF CAMM-GL III INSTRUCTIONS*1: -(226-1) — +(226-1) *2: 0 — +(226-1) *3: -(226-1)° — +(226-1)° *4: 21(16) — 3A(16), 3C(16) — 7E(16)• mode1Ins

19Instruction Format Meaning of Parameter [Parameter Range (Default)] Explanation!NR !NR [terminator] None Not Ready!PG !PG n [terminator] n: [-1600

209 LIST OF DEVICE CONTROL INSTRUCTIONSDevice control instructions are used to determine the communication sequence between the PNC-900 and computer t

21Error Possible causecode and action0 No I/O errors10 Cause: after execution of an output command, other output instructions are sent before the outp

2210 LIST OF OPTIONSOption name Product number DescriptionSpare blade (for ZEC-U1005 Cemented carbide blade (5 pcs/set)standard vinyl sheet)Spare bl

23Mechanism Media-movement methodAcceptable sheet widths 50 mm ~ 305 mm (1-15/16" ~ 12")Maximum cutting area Width: 280 mm (11")Length:

iTypographic ConventionsThis manual uses certain typographic symbols, outlined below.This indicates a point requiring particular care to ensure safe u

24• Interface SpecificationsSignal numberTerminal numberSignal numberPin ConnectionNC 36 18 HIGH**HIGH* 35 17 GNDNC 34 16 GNDGND 33 15 NCHIGH* 32 14 N

A3020195BE V4-1

ii To Ensure Safe UseIf you find some abnormality, immediately turn off the power switch and check the user's manual to findout what is wrong. CA

iii About the Labels Affixed to the UnitThese labels are affixed to the body of this product. The following figure describes the location andcontent

ivTo Ensure Correct Use NOTICEDo not install in an area subject todust or high humidity or with poorventilation.321 NOTICEWhen the unit is not in us

1Copyright © 1993 ROLAND DG CORPORATIONThanks and Best WishesThank you very much for purchasing the CAMM-1 PNC-900.Since we wish you many years of pro

21 PRECAUTIONS• When Moving the PNC-900...Do not try to pick up or move the PNC-900 by grasping the top area of the unit -- be sure to use both hands

33 PART NAMES AND FUNCTIONS• Front ViewTool CarriageThe tool carriage is where theblade holder is mounted. Thetool carriage performs thecutting by mov